ABS Grade EQ70 Shipbuilding Steel Plate Chemical Composition and Mechanical Property C max Si max Mn P max S max N max. 0.20 0.55 1.70 0.025 0.025 0.020 Yield Strength (MPa) min. Tensile Strength (MPa) Elongation min. % 690 770-940 14
Spec Status Description; GL-1:Active:The designation API GL-1 denotes lubricants intended for manual transmissions operating under such mild conditions that straight petroleum or refined petroleum oil may be used satisfactorily. Oxidation and rust inhibitors, defoamers, and pour depressants may be added to improve the characteristics of these FUEL ETHANOL INDUSTRY GUIDELINES, content. The new test fuel specifications apply to new vehicle certification, assembly line, and in-use testing. EPA is also setting test fuel specifications for Flex Fuel (E85) for the first time. The industry is still evolving and we continue to grow ethanol in the fuel supply. From a vehicle use
SAE 80W90 or 80W grade multifunction hypoid gear oil. Meets API GL-5 and MIL-L-2105C. Ford N052145 VX00 VW G 052 145 equivalent Ford specification. Fully synthetic, meets API GL-4 and SAE 75W90. Automatic Transmission Fluids Ford Mercon Automatic transmission fluid specification for use in Ford automatic transmissions. Forc Mercon V GENUINE VOLVO LUBRICANTS and coolants Industry and Builder Specifications Volvo Transmission Oil 97304. Super transmission oil is semi synthetic and rated for use in API GL-5. Industry and Builder Specifications - SAE 80W-140 GL-5:API GL-5 - Scania STO 1:0 SUPER gear OIL Good oil
GM 4.3L-262ci-V6 Engine Torque Specs. Over 6,000 Automotive Torque Specs. Search Car Torque Specifications by Engine or Model Gear Oil SAE 90 API GL-4 & GL-5 - DANA LUBESGear Oil SAE 90 API GL-4 & GL-5 Gear Oil SAE 90 API GL-4 & GL-5 are lubricating gear oils for mechanical transmissions based on high quality base oils and additives that are a balanced combination of active ingredients. High pressure agents and other additives offer good wear protection under harsh operating conditions. Applications :API GL-5 API GL-4 Features and
requirements for Grade D breathing air described in ANSI/Compressed Gas Association Commodity Specification for Air, G-7.1-1989, to include:p Oxygen content (v/v) of 19.5% - 23.5%; p Hydrocarbon (condensed) content of 5 milligrams per cubic meter of air or less; p Carbon monoxide (CO) content of 10 parts per million (ppm) or less; LG Velvet 5G - Full phone specificationsLG Velvet 5G Android smartphone. Announced May 2020. Features 6.8 display, Snapdragon 765G 5G chipset, 4300 mAh battery, 128 GB storage, 8 GB RAM, MIL-STD-810G compliant.
GL-4 SAE 75W-90, XT-4-QGL Ford Spec WSS-M2C203-A1 Synchromesh MTF 2010-12 Ford Fusion 2011-12 Lincoln MKZ 2010-11 Mercury Milan GL-4 SAE 75W-90, XT-4-QGL Ford Spec WSS-M2C203-A2 Synchromesh MTF 2011-12 Ford Fiesta SLF PN XT-M5-QS, Spec WSS-M2C200-C Available from dealer 2005-08 Ford GT SLF QT-75W90-QGT Available from Mercedes-Benz Specifications for Operating Fluids The Mercedes-Benz Specifications for Operating Fluids provide you with an overview of the requirements for the operating fluids and for the recommended products. Operating Fluids are products necessary for Mercedes-vehicles / major assemblies, e.g. fuel, engine oil, gear oil, ATF, brake fluid, coolant, windshield washer fluid etc.
NV D36|DNV D36 shipbuilding and offshore platform steel plate 201382 by admin Gangsteel is specialized in supplying high strength steel plate in Grade D36 approved by DNV, ABS, RINA, LR, GL, BV, CCS, NK and KR.. For more information of DNV Grade D36 steel plate, please check them in following: PPTC Entrance Assessment (GL) The Transfer TestPPTC Post Primary Transfer Consortium Schools which accept the PPTC's Entrance Assessment (GL) results as part of their selection criteria for admission to Year 8 (Form 1) are listed at the bottom of the page. Entrance Assessment (GL) The PPTC Entrance Assessment is commonly referred to as the GL, GL Test or GL Assessment. The assessment consists of 2 standardised
The viscosity grade of a lube oil is determined by the Society of Automotive Engineers (SAE). Oils can be separated into multigrade oils and monograde oils. Multigrade oils must fulfill two viscosity specifications, their viscosity grade consists of two numbers, e.g. 10W-40:10W refers to the low-temperature viscosity ("Winter"), 40 refers to SECTION 02310 HORIZONTAL DIRECTIONAL DRILLINGGrade P345 Polyethylene Material as defined in ASTM Specification D-1248 (PE 3408). The minimum pressure class/SDR rating acceptable shall be Class 200/SDR 11. The pipe shall be DIPS and shall have an interior diameter no less than the piping that it is connected to. 2. Joints:Joints shall be of a heat fusion joining system. Pipe and
We keep more than 100,000 tons steel in stock every month, this is enough to meet the buyers' ex-stock requirement .At the same time, this huge stock amount also can meet our process requirement . Our company has a large plant and machinery processing equipment, CNC cutting machine, CNC horizontal boring and milling machine, grinder, program-controlled beam milling Structural grading WoodSolutionsIn-grade testing and/or verification - deriving the respective grade properties using in-grade test data. An overview of the structural grading systems is provided in the presentation Structural Grading which is available for download below. The F-grade system An F-grade is a name for the grouping of the timber.
Sep 29, 2015 · Metric plywood is manufactured according to a European standard. It is termed GL-1 or GL-2, the GL meaning German Lloyd. GL-1 is a more strict specification than GL-2 that allows more defects. Metric plywood obviously is measured using the metric system with 1.5mm (approximately 1/16 inch) being a common thickness. WHICH AUTOMOTIVE GEAR OIL SHOULD I USE? TransDieselAPI GL-4 classifies passenger car and light truck manual gear box lubricants and oils used in tractor gearboxes and spiral bevel gear final drives. API GL-5 defines passenger car, light and heavy truck and bus hypoid final drives where there is
Nov 14, 2017 · This specification includes a comprehensive set of test requirements that address the shortcomings of API Category GL-5 and ensure that lubricants meeting this specification will provide the performance required by todays modern equipment. One of these tests is the ASTM D5704 test, commonly referred to as the L-60-1 test.AB DQ47 Shipbuilding Steel Plate Supplier, China The shipbuilding steel grade is ABS grade DQ47. The steel grade is equivalent with CCS DH460, BV DH460, NV D460, GL-D460, KR DH47, LR DH46, KD47, and RINA-D460. It is a kind of marine steel plate. It features high tensile strength, and the minimum yield strength of the steel plate is 460MPa.